Transformador de iluminación RS PRO, 230V ac, 12V, 20 → 105W, Electrónico
Documentos Técnicos
Especificaciones
Brand
RS ProTensión nominal primaria
230V ac
Tensión nominal secundaria
12V
Potencia Nominal
20 → 105W
Dimensiones
107 x 35 x 21 mm
Largo
107 mm
Profundidad
35 mm
Profundidad
21 mm
Requisito de carga mínimo
20W
Temperatura mínima
-20°C
Temperatura Máxima
+55°C
Peso
80 g
Tipo
Electronic
Atenuación
Atenuación
Método de atenuación
Salida
Frecuencia de funcionamiento mínima
50Hz
Tipo de terminación
Screw
Características de protección
Protección contra sobrecorriente, protección contra exceso de temperatura, protección contra sobrecarga, protección contra cortocircuito
Frecuencia Máxima de Funcionamiento
60Hz
País de Origen
Italy
Datos del producto
Low Voltage Lighting Transformers
Dimming Methods (where applicable):
Leading Edge:
The control device is either a thyristor or triac which blocks power until they are switched on by the control signal. At that point the current flows almost instantaneously and continues to flow until the end of the half cycle of the mains waveform. When the signal reaches zero, the device turns off and no more current is passed until it is triggered again. Turning the power on and off in this manner averages out creating a constant intensity level and by altering the precise trigger point over a period of time the lamp can be dimmed.
Trailing Edge:
Since this method of dimming uses transistor technology it is not limited to just switching, therefore current can be controlled gradually. Transistors can be programmed to pass current at the start of each half cycle, and gradually switch off later. This will control the full amount of power reaching the lamp without the side effects of a step increase in current.
Volver a intentar más tarde
Vuelva a verificar más tarde.
$ 17.108
Each (Sin IVA)
$ 20.359
Each (IVA Incluido)
1
$ 17.108
Each (Sin IVA)
$ 20.359
Each (IVA Incluido)
1
Documentos Técnicos
Especificaciones
Brand
RS ProTensión nominal primaria
230V ac
Tensión nominal secundaria
12V
Potencia Nominal
20 → 105W
Dimensiones
107 x 35 x 21 mm
Largo
107 mm
Profundidad
35 mm
Profundidad
21 mm
Requisito de carga mínimo
20W
Temperatura mínima
-20°C
Temperatura Máxima
+55°C
Peso
80 g
Tipo
Electronic
Atenuación
Atenuación
Método de atenuación
Salida
Frecuencia de funcionamiento mínima
50Hz
Tipo de terminación
Screw
Características de protección
Protección contra sobrecorriente, protección contra exceso de temperatura, protección contra sobrecarga, protección contra cortocircuito
Frecuencia Máxima de Funcionamiento
60Hz
País de Origen
Italy
Datos del producto
Low Voltage Lighting Transformers
Dimming Methods (where applicable):
Leading Edge:
The control device is either a thyristor or triac which blocks power until they are switched on by the control signal. At that point the current flows almost instantaneously and continues to flow until the end of the half cycle of the mains waveform. When the signal reaches zero, the device turns off and no more current is passed until it is triggered again. Turning the power on and off in this manner averages out creating a constant intensity level and by altering the precise trigger point over a period of time the lamp can be dimmed.
Trailing Edge:
Since this method of dimming uses transistor technology it is not limited to just switching, therefore current can be controlled gradually. Transistors can be programmed to pass current at the start of each half cycle, and gradually switch off later. This will control the full amount of power reaching the lamp without the side effects of a step increase in current.