
Documentos Técnicos
Especificaciones
Brand
RS ProTipo de producto
Data Logger
Número de modelo
PRO-USB-1
Precisión
±0.5°C, ±0.5 °C
Número de Canales
1
Parámetros medidos
Temperature
Tipo de Interfaz
USB
Tipo de registrador de datos
Temperature
Potencia de la Fuente
Battery
Grado de protección IP
IP40
Mínima Temperatura de Funcionamiento
-35°C
Máxima Temperatura de Funcionamiento
80°C
Longitud
99mm
Certificación de atmósferas explosivas
No
Certificaciones y estándares
RoHS
Anchura
25mm
Altura
23mm
Número de Lecturas por Canal
16000
Tipo de Batería
Ión-litio
Vida Útil de la Batería
2year
Alarma
Yes
Calibrated
UKAS
País de Origen
China
Datos del producto
Introducing the RS PRO USB Temperature Data Logger. This high-quality standalone unit can measure and store up to 16,000 temperature readings from -35 to +80°C and is also IP 67 rated which means it is resistant against water, dust and debris, making it ideal for use in difficult or inhospitable environments. This data logger unit is compact, portable and incredibly versatile and can easily be set up to view the data by using the built in USB interface, making it easy to access the measured data in situ or later for review.
Yes, the RS PRO Data Logger is supplied as a stand-alone ready-to-use device with the battery and all necessary accessories
The battery life depends on your logger's settings, but it should last approximately 2 years (at 25°C and 1-minute logging rate)
If the LEDs flash sequentially it may indicate that there is a problem with the battery. This could be a flat battery or a battery where a passivation layer has formed. Leaving the data logger connected to a PC for about 30 seconds and re-installing the batteries to reset the data logger will solve the issue.
If you see the sequential LEDs after disconnecting the logger from a PC then the logging session will not start. You should check the battery condition and then repeat the setup procedure using the PC software.
The logger is protected against ingress from water and dust to IP67 standard when the cap is fitted so can be safely used both inside and outside
The full set contains the logger, battery and a wall mount clip for easy installation
https://s3.amazonaws.com/lascar_downloads/EasyLogUSB+Installer.exe
Volver a intentar más tarde
$ 187.551
$ 187.551 Each (Sin IVA)
$ 223.186
$ 223.186 Each (IVA Inc.)
Tipo de calibración
Calibración UKAS
1
$ 187.551
$ 187.551 Each (Sin IVA)
$ 223.186
$ 223.186 Each (IVA Inc.)
Volver a intentar más tarde
Tipo de calibración
Calibración UKAS
1
Documentos Técnicos
Especificaciones
Brand
RS ProTipo de producto
Data Logger
Número de modelo
PRO-USB-1
Precisión
±0.5°C, ±0.5 °C
Número de Canales
1
Parámetros medidos
Temperature
Tipo de Interfaz
USB
Tipo de registrador de datos
Temperature
Potencia de la Fuente
Battery
Grado de protección IP
IP40
Mínima Temperatura de Funcionamiento
-35°C
Máxima Temperatura de Funcionamiento
80°C
Longitud
99mm
Certificación de atmósferas explosivas
No
Certificaciones y estándares
RoHS
Anchura
25mm
Altura
23mm
Número de Lecturas por Canal
16000
Tipo de Batería
Ión-litio
Vida Útil de la Batería
2year
Alarma
Yes
Calibrated
UKAS
País de Origen
China
Datos del producto
Introducing the RS PRO USB Temperature Data Logger. This high-quality standalone unit can measure and store up to 16,000 temperature readings from -35 to +80°C and is also IP 67 rated which means it is resistant against water, dust and debris, making it ideal for use in difficult or inhospitable environments. This data logger unit is compact, portable and incredibly versatile and can easily be set up to view the data by using the built in USB interface, making it easy to access the measured data in situ or later for review.
Yes, the RS PRO Data Logger is supplied as a stand-alone ready-to-use device with the battery and all necessary accessories
The battery life depends on your logger's settings, but it should last approximately 2 years (at 25°C and 1-minute logging rate)
If the LEDs flash sequentially it may indicate that there is a problem with the battery. This could be a flat battery or a battery where a passivation layer has formed. Leaving the data logger connected to a PC for about 30 seconds and re-installing the batteries to reset the data logger will solve the issue.
If you see the sequential LEDs after disconnecting the logger from a PC then the logging session will not start. You should check the battery condition and then repeat the setup procedure using the PC software.
The logger is protected against ingress from water and dust to IP67 standard when the cap is fitted so can be safely used both inside and outside
The full set contains the logger, battery and a wall mount clip for easy installation
https://s3.amazonaws.com/lascar_downloads/EasyLogUSB+Installer.exe