Transformador de iluminación GE, 220 → 240V, 12V, 20 → 60W
Documentos Técnicos
Especificaciones
Brand
GETensión nominal primaria
220 → 240V
Tensión nominal secundaria
12V
Potencia Nominal
20 → 60W
Dimensiones del Cuerpo
109 x 40 x 20,5 mm
Largo
109 mm
Profundidad
40 mm
Profundidad
20.5 mm
Número de fases
1
Tipo de terminación
Screw
País de Origen
China
Datos del producto
Transformador electrónico atenuable GE Lighting de 12 V
Este transformador electrónico de 12 V viene en un nuevo diseño de tamaño compacto, lo que lo convierte en la elección ideal para aplicaciones de iluminación delicadas. Las aplicaciones idóneas para este transformador electrónico de GE son oficinas, hospitales, tiendas, hoteles, supermercados, aeropuertos, metros y estaciones de tren.
Conector de terminal que reduce el tiempo de funcionamiento
Eficiencia y fiabilidad altas
Alto factor de potencia, THD bajo
Vida útil media: 20.000 horas
Approvals
CE, CB
Harmonic: IEC 61000-3-2
EMC: IEC 61547
EMI: CISPR15
Safety: IEC 61347-1, IEC 61347-2-3
Low Voltage Lighting Transformers
Dimming Methods (where applicable):
Leading Edge:
The control device is either a thyristor or triac which blocks power until they are switched on by the control signal. At that point the current flows almost instantaneously and continues to flow until the end of the half cycle of the mains waveform. When the signal reaches zero, the device turns off and no more current is passed until it is triggered again. Turning the power on and off in this manner averages out creating a constant intensity level and by altering the precise trigger point over a period of time the lamp can be dimmed.
Trailing Edge:
Since this method of dimming uses transistor technology it is not limited to just switching, therefore current can be controlled gradually. Transistors can be programmed to pass current at the start of each half cycle, and gradually switch off later. This will control the full amount of power reaching the lamp without the side effects of a step increase in current.
Volver a intentar más tarde
Vuelva a verificar más tarde.
P.O.A.
1
P.O.A.
1
Documentos Técnicos
Especificaciones
Brand
GETensión nominal primaria
220 → 240V
Tensión nominal secundaria
12V
Potencia Nominal
20 → 60W
Dimensiones del Cuerpo
109 x 40 x 20,5 mm
Largo
109 mm
Profundidad
40 mm
Profundidad
20.5 mm
Número de fases
1
Tipo de terminación
Screw
País de Origen
China
Datos del producto
Transformador electrónico atenuable GE Lighting de 12 V
Este transformador electrónico de 12 V viene en un nuevo diseño de tamaño compacto, lo que lo convierte en la elección ideal para aplicaciones de iluminación delicadas. Las aplicaciones idóneas para este transformador electrónico de GE son oficinas, hospitales, tiendas, hoteles, supermercados, aeropuertos, metros y estaciones de tren.
Conector de terminal que reduce el tiempo de funcionamiento
Eficiencia y fiabilidad altas
Alto factor de potencia, THD bajo
Vida útil media: 20.000 horas
Approvals
CE, CB
Harmonic: IEC 61000-3-2
EMC: IEC 61547
EMI: CISPR15
Safety: IEC 61347-1, IEC 61347-2-3
Low Voltage Lighting Transformers
Dimming Methods (where applicable):
Leading Edge:
The control device is either a thyristor or triac which blocks power until they are switched on by the control signal. At that point the current flows almost instantaneously and continues to flow until the end of the half cycle of the mains waveform. When the signal reaches zero, the device turns off and no more current is passed until it is triggered again. Turning the power on and off in this manner averages out creating a constant intensity level and by altering the precise trigger point over a period of time the lamp can be dimmed.
Trailing Edge:
Since this method of dimming uses transistor technology it is not limited to just switching, therefore current can be controlled gradually. Transistors can be programmed to pass current at the start of each half cycle, and gradually switch off later. This will control the full amount of power reaching the lamp without the side effects of a step increase in current.